![Image](http://i64.photobucket.com/albums/h186/waldco/instrumental/woodpipe.gif)
Well, I don't think I have a practical way of hollowing out the wood, so I'm thinking I may try it with some bamboo or something.
Any suggestions on how to go about this?
Assuming one didn't have power tools, what would one use?brewerpaul wrote:This is the best way to do it:
http://en.wikipedia.org/wiki/Gun_drill
nice straight holes, with very little wandering. Bad
news is that they're expensive.
And it's not just the drill...you'll need a drill, some kind of machine to power either it or the wood--like a lathe, not a hand drill, an adapter to fit the drill to the machine (most likely), and definitely an air compressor. Believe me, I started out trying to save money by leaving some of these out when I was first doing my testing, with less than satisfactory results.brewerpaul wrote:This is the best way to do it:
http://en.wikipedia.org/wiki/Gun_drill
nice straight holes, with very little wandering. Bad news is that they're expensive.
Very true: to use my gundrill, I mount it in the tailstock of my lathe and connect it to an air compressor which blows out the chips that are formed. The wood is chucked at one end in the lathe chuck, and the free end is supported by a "steadyrest" which was custom made for my by Glenn Schultz.Wanderer wrote:And it's not just the drill...you'll need a drill, some kind of machine to power either it or the wood--like a lathe, not a hand drill, an adapter to fit the drill to the machine (most likely), and definitely an air compressor. Believe me, I started out trying to save money by leaving some of these out when I was first doing my testing, with less than satisfactory results.brewerpaul wrote:This is the best way to do it:
http://en.wikipedia.org/wiki/Gun_drill
nice straight holes, with very little wandering. Bad news is that they're expensive.
It's possible to use a contractor's/installer's bit. I had some luck with one, was able to drill a few holes up to about 15". I had less luck with spade bits; they just really like to wander. If you want to go that route, you might want to PM/email Lucas, who uses them. Contractor bits come in 1/2" diameters with a 3/8 shank.Lark wrote:I, like Walden, am trying to find a way to hollow out the wood. Now I have a lathe, with a 3/8 hollow centre on the tale stock. Now I’ve read that a shell, or lamp, auger is the best tool to drill a straight hole through the blank, but who sells them in North America? All I can find are sellers based in the UK. Can I use a 3/8 installer’s bit instead? Or another kind of a bit?
Once I have my straight 3/8 hole through the blank, how do I enlarge it to the size I want? I imagine using a long spade bit with the spurs ground off, but this seems problematic to me. Is there another way?
Yes, I can play an A on tabor pipe. Here're the fingerings.Innocent Bystander wrote: According to the information I've found on the Web, I should be able to
overblow the D to get an A, a d, an a and a d'. No problems with the D, d
and d' (and even a d'') but I can't get an A. Any A. Is there a technique I
need to practice, or am I just misinformed or deluded?
I actually am able to drill blanks in about 5 minutes. I got my drill from Danjon, and the guy said he'd put a different geometry on it for wood (though what makes it different than a metal-drilling one, I couldn't say).chas wrote:
But, as Paul and Greg have said, the gundrill is really the way to go. Between checking that the hole is true, clearing out chips, and all that, it would take at least 2 hours to drill through a 12" blank with a contractor's bit, while it takes maybe 15 minutes with a gundrill. (I don't use a compressor, but a foot pump to clear the chips. If someone can point me to a quiet compact compressor, I'd appreciate it.) It's not cheap; the drill was less than $100, the adaptor for an MT2 taper was somewhat more. I won't need an adaptor for each subsequent drill, tough. But if you consider that you'll save at least 1.5 hours with each bore you make, it's worth it.