Good Plane for Reducing Cane Slips
- Ceann Cromtha
- Posts: 883
- Joined: Mon Aug 01, 2005 5:03 pm
- antispam: No
- Please enter the next number in sequence: 8
- Tell us something.: I’m changing my location to my actual address. My previous location was a reference to Joyce’s Finnegans Wake.
- Location: Baltimore, Maryland USA
Good Plane for Reducing Cane Slips
Could someone please recommend a good plane for shaving the sides of the cane slips to bring them down to the proper width? I’ve had two that I’ve bought at local hardware stores and they don’t do a good job of it (despite regularly sharpening the blades in them). I think that the blades in my planes are simply too thick and they tend to mash into the cane instead of shaving slivers off of it. Thanks!
- daveboling
- Posts: 4909
- Joined: Sun Feb 17, 2002 6:00 pm
- antispam: No
- Please enter the next number in sequence: 8
- Location: Huntsville, AL
Re: Good Plane for Reducing Cane Slips
I use an old Stanley No.60 low angle block plane. It has a Hock blade, and I've used it for reeds, boat building, and harp building. I can literally produce a shaving of oak or cedar you can read through (and my skill with a plane is far less than some I know). For any plane, the edge angles and how sharp it is make the most difference.
If you want to start a fight/flame war amongst wood boat builders, suggest two numbers as the best for primary and secondary bevel angles, and the step back a watch the fray...
dave boling
If you want to start a fight/flame war amongst wood boat builders, suggest two numbers as the best for primary and secondary bevel angles, and the step back a watch the fray...
dave boling
I teleported home one night
With Ron and Sid and Meg.
Ron stole Meggie's heart away
And I got Sidney's leg.
-- Douglas Adams
'Bundinn er bátlaus maðu'.
With Ron and Sid and Meg.
Ron stole Meggie's heart away
And I got Sidney's leg.
-- Douglas Adams
'Bundinn er bátlaus maðu'.
- myrddinemrys
- Posts: 645
- Joined: Sat Jan 22, 2005 9:34 am
- antispam: No
- Please enter the next number in sequence: 8
- Tell us something.: Something something Something something Something something Something something Something something Something something Something something Something something.
- Location: Ravenna, OH
- Contact:
Re: Good Plane for Reducing Cane Slips
I use a China special from Home Depot. Keep a keen edge and set your blade height real low.
Wild Goose Studios Music, reed making and pipe making.
- an seanduine
- Posts: 1997
- Joined: Sun Sep 13, 2009 10:06 pm
- antispam: No
- Location: just outside Xanadu
Re: Good Plane for Reducing Cane Slips
Thread Drift Alert:
I make slips out of Western Red Cedar, Thuja Plicata, not cane. The slips are flat, not curved. I fasten the slips on a block of known thickness, then run them through my fairly inexpensive Ryobi planer. I can readily make slips of between .085 to .095 inches thickness, in increments of about .001 inch.
Initially then I ´bend´ a curvature in the slips by lashing them to blocks of my target curvature.
I would propose something like a router table with a ´profile blade´ could possibly be used on cane. Sharpness of the blade would be critical.
Legere reeds use a CNC setup to accomplish cutting curvature into their Bassoon Slips made of synthetic material with a rotary single tooth diamond blade. They tell me they are working toward making some kind of Uilleann Chanter Reed, but it has been two years, and I may die before that comes down the pike.
Bob
I make slips out of Western Red Cedar, Thuja Plicata, not cane. The slips are flat, not curved. I fasten the slips on a block of known thickness, then run them through my fairly inexpensive Ryobi planer. I can readily make slips of between .085 to .095 inches thickness, in increments of about .001 inch.
Initially then I ´bend´ a curvature in the slips by lashing them to blocks of my target curvature.
I would propose something like a router table with a ´profile blade´ could possibly be used on cane. Sharpness of the blade would be critical.
Legere reeds use a CNC setup to accomplish cutting curvature into their Bassoon Slips made of synthetic material with a rotary single tooth diamond blade. They tell me they are working toward making some kind of Uilleann Chanter Reed, but it has been two years, and I may die before that comes down the pike.
Bob
Not everything you can count, counts. And not everything that counts, can be counted
The Expert's Mind has few possibilities.
The Beginner's mind has endless possibilities.
Shunryu Suzuki, Roshi
The Expert's Mind has few possibilities.
The Beginner's mind has endless possibilities.
Shunryu Suzuki, Roshi
-
- Posts: 174
- Joined: Fri Nov 16, 2007 6:23 pm
- antispam: No
- Please enter the next number in sequence: 8
- Location: Blue Mountains, NSW, AU.
Re: Good Plane for Reducing Cane Slips
Stanley 220. Low angle. Cheap second hand.
- ausdag
- Posts: 1881
- Joined: Sat Jul 24, 2004 7:14 am
- Please enter the next number in sequence: 1
- Location: Brisbane, AUSTRALIA
Re: Good Plane for Reducing Cane Slips
I have good results with a Veritas Miniature Low-Angle block plane which I use primarily to plane nice straight tails before shaping further if needed on the sanding cylinder:
https://www.leevalley.com/en-us/shop/to ... em=05P8220
https://www.leevalley.com/en-us/shop/to ... em=05P8220
David (ausdag) Goldsworthy
http://ozuilleann.weebly.com/
http://ozuilleann.weebly.com/
- Ceann Cromtha
- Posts: 883
- Joined: Mon Aug 01, 2005 5:03 pm
- antispam: No
- Please enter the next number in sequence: 8
- Tell us something.: I’m changing my location to my actual address. My previous location was a reference to Joyce’s Finnegans Wake.
- Location: Baltimore, Maryland USA
Re: Good Plane for Reducing Cane Slips
Thanks all!
-
- Posts: 133
- Joined: Mon Mar 16, 2009 2:19 am
- antispam: No
- Please enter the next number in sequence: 8
- Tell us something.: I play various instruments, Highland pipes, Border pipes, uilleann pipes, smallpipes, flute (badly) and trying to learn mandolin.
- Location: Essex, U.K
- Contact:
Re: Good Plane for Reducing Cane Slips
Thats a nice wee tool might have to get one myself.ausdag wrote: ↑Tue Jan 25, 2022 5:15 pm I have good results with a Veritas Miniature Low-Angle block plane which I use primarily to plane nice straight tails before shaping further if needed on the sanding cylinder:
https://www.leevalley.com/en-us/shop/to ... em=05P8220
I used a cheapy for a while by Faithfull but currently I'm using this one.
https://www.workshopheaven.com/quangshe ... JEEALw_wcB
Its worth spending time setting the plane up and ensuring that the sole is flat, plenty of info about tweaking planes.
https://www.woodmagazine.com/woodworkin ... ane-basics
https://www.youtube.com/watch?v=eFw--HUkWTc
I like to offset my blade so I can vary the amount I shave off by using a different part of the plane.
Iain
- Ceann Cromtha
- Posts: 883
- Joined: Mon Aug 01, 2005 5:03 pm
- antispam: No
- Please enter the next number in sequence: 8
- Tell us something.: I’m changing my location to my actual address. My previous location was a reference to Joyce’s Finnegans Wake.
- Location: Baltimore, Maryland USA
Re: Good Plane for Reducing Cane Slips
Great stuff, Iain. Very helpful, thanks!
- BzzzzT
- Posts: 160
- Joined: Wed Sep 22, 2004 8:38 pm
- antispam: No
- Please enter the next number in sequence: 10
- Location: Arizona
- Contact:
Re: Good Plane for Reducing Cane Slips
My favorite plane, is a chisel plane for the edges. It's easy to sharpen and set up, unlike a normal plane.
https://www.rockler.com/bench-dog-no-92-shoulder-plane
To bring down the slip, I use a paring chisel. Blue Spruce makes good modern paring chisels. Mine is Victorian and around an inch.
https://bluesprucetoolworks.com/collect ... ing-chisel
https://www.rockler.com/bench-dog-no-92-shoulder-plane
To bring down the slip, I use a paring chisel. Blue Spruce makes good modern paring chisels. Mine is Victorian and around an inch.
https://bluesprucetoolworks.com/collect ... ing-chisel