Bellows Metal Hinge

A forum about Uilleann (Irish) pipes and the surly people who play them.
User avatar
gariwerd
Posts: 131
Joined: Thu Apr 22, 2010 3:24 am
antispam: No
Location: Victoria, Australia

Bellows Metal Hinge

Post by gariwerd »

Can anybody advise me where to source a metal hinge suitable for uilleann bellows?
geoff wooff
Posts: 633
Joined: Sat Apr 20, 2013 3:12 am
antispam: No
Please enter the next number in sequence: 8
Location: centre France

Re: Bellows Metal Hinge

Post by geoff wooff »

What sort of hinge are you looking for , as in what faces do you wish to mount it to ?
User avatar
gariwerd
Posts: 131
Joined: Thu Apr 22, 2010 3:24 am
antispam: No
Location: Victoria, Australia

Re: Bellows Metal Hinge

Post by gariwerd »

To be mounted on the 2 wooden paddles.
m4malious
Posts: 174
Joined: Fri Nov 16, 2007 6:23 pm
antispam: No
Please enter the next number in sequence: 8
Location: Blue Mountains, NSW, AU.

Re: Bellows Metal Hinge

Post by m4malious »

With any deep metal hinge, there is the need for the 2nd fold of each leaf at right angles to accomodate the bellows cheek orientation.
Possible to make those additional folds, one guesses, on something like this - https://www.ebay.com.au/itm/311330878858 - but lot of work rather than just a single strip of leather belt type hinge.
M
User avatar
an seanduine
Posts: 1997
Joined: Sun Sep 13, 2009 10:06 pm
antispam: No
Location: just outside Xanadu

Re: Bellows Metal Hinge

Post by an seanduine »

Here´s a discussion with some pictures:viewtopic.php?f=6&t=66616&start=15

Bob

edited to add: from Richard Patkos https://reverb.com/item/9234629-patkos- ... od-leather
Not everything you can count, counts. And not everything that counts, can be counted

The Expert's Mind has few possibilities.
The Beginner's mind has endless possibilities.
Shunryu Suzuki, Roshi
geoff wooff
Posts: 633
Joined: Sat Apr 20, 2013 3:12 am
antispam: No
Please enter the next number in sequence: 8
Location: centre France

Re: Bellows Metal Hinge

Post by geoff wooff »

The metal hinges shown in the articles cited on this thread all have very short bearing surfaces. I make a hinge, all turned on the lathe, with two bearing surfaces of 15mm long x 6.25mm diameter. These hinges fit between the bellows boards in a similar way to the Taylor type. One very heavily used brass example has completed 25 years of piping. It is simple to make and especially durable in Nickel Silver or Stainless Steel.

Anyone wanting pictures can contact me.
User avatar
Mr.Gumby
Posts: 6606
Joined: Mon Jun 07, 2010 11:31 am
antispam: No
Please enter the next number in sequence: 8
Location: the Back of Beyond

Re: Bellows Metal Hinge

Post by Mr.Gumby »

One very heavily used brass example has completed 25 years of piping.
Mine is still going, since 1986, and I have put the mileage on it.
My brain hurts

Image
geoff wooff
Posts: 633
Joined: Sat Apr 20, 2013 3:12 am
antispam: No
Please enter the next number in sequence: 8
Location: centre France

Re: Bellows Metal Hinge

Post by geoff wooff »

Indeed Peter!
It being the Nickel Silver version 35 years of everyday Piping. How many hours do you think ? 15- 20,000 hours.... more ?
User avatar
Mr.Gumby
Posts: 6606
Joined: Mon Jun 07, 2010 11:31 am
antispam: No
Please enter the next number in sequence: 8
Location: the Back of Beyond

Re: Bellows Metal Hinge

Post by Mr.Gumby »

Hmm, probably managed that much in the first twenty years. :boggle:
My brain hurts

Image
m4malious
Posts: 174
Joined: Fri Nov 16, 2007 6:23 pm
antispam: No
Please enter the next number in sequence: 8
Location: Blue Mountains, NSW, AU.

Re: Bellows Metal Hinge

Post by m4malious »

Brass version of the Woof design - about 15 years (speaking from personal experience). Probably ran too heavy reeds for a long time.
Will have to look at replacing the worn parts with nickel silver - to see out this lifetime - based upon what you say Geoff. :thumbsup:
M
User avatar
gariwerd
Posts: 131
Joined: Thu Apr 22, 2010 3:24 am
antispam: No
Location: Victoria, Australia

Re: Bellows Metal Hinge

Post by gariwerd »

Thanks for your responses. The reason why I asked is that I have bellows that are not working efficiently and I think the reason is that the leather hinge has become distorted and when the bellows are closed the two sides are significantly offset (4-5 cms). This hinge is not a very thick piece of leather. I have seen other bellows with much much thicker leather hinges and these would be more stable I am sure but I was thinking a metal hinge would be even better. The idea of modifying a parliament hinge seems to be workable to me and I think I will try it. Brass is a fairly soft metal so folding it should be possible with care. If successful I will advise you.
User avatar
rorybbellows
Posts: 3191
Joined: Sun Dec 14, 2003 7:50 am
antispam: No
Please enter the next number in sequence: 10
Location: the cutting edge

Re: Bellows Metal Hinge

Post by rorybbellows »

This type of hinge contains a ball bearing rated to 35000rpm for 8 hours continuous use. A bellows hinge doesn't even do a quarter revolution so that makes the hinge rated to 140,000 ppm for 8 hours. The bearing is also guaranteed for three years. If you play continuously for three hours every day the hinge will last for 533 years.

Image
Image
RORY
I'm Spartacus .
User avatar
RLines
Posts: 325
Joined: Wed Sep 24, 2008 10:05 am
antispam: No
Please enter the next number in sequence: 8
Tell us something.: Uilleann Piper. Gramophone Enthusiast. Piping Art Collector. Co-chair Pibyddion Uilleann Cymru. Board Member NPU.
Location: Glan y Fferi, Wales

Re: Bellows Metal Hinge

Post by RLines »

Bit of a different design on my 1930s Patsy Brown bellows. Works very well.

Image
Image
Image
My Twitter: @FerrysidePiper
My YouTube
Club Twitter: @UilleannCymru
User avatar
gariwerd
Posts: 131
Joined: Thu Apr 22, 2010 3:24 am
antispam: No
Location: Victoria, Australia

Re: Bellows Metal Hinge

Post by gariwerd »

Do you know where that hinge you posted can be sourced Rory?
User avatar
rorybbellows
Posts: 3191
Joined: Sun Dec 14, 2003 7:50 am
antispam: No
Please enter the next number in sequence: 10
Location: the cutting edge

Re: Bellows Metal Hinge

Post by rorybbellows »

gariwerd wrote: Tue Oct 19, 2021 1:41 am Do you know where that hinge you posted can be sourced Rory?
As with the other hinges pictured, I suspect they are made in house by the pipe maker, the one I posted is by Mark Donohoe.
RORY
I'm Spartacus .
Post Reply