Hey Aanvil,
The bottom D was strong with the Burns Rudall headjoint! But I don't tend to really honk the bottom D.
You might check the seal on the bottom tennon. I enclosed extra official Burns waxed thread for just such a purpose.
If this body & foot displease you, I'll offer a refund (less postage).
Good luck and hope you can get to the root of the problem!
SOLD - Two Flutes and a Body
- Jack Bradshaw
- Posts: 933
- Joined: Thu May 01, 2003 2:49 pm
- Please enter the next number in sequence: 1
- Location: Hampstead, NH
- Contact:
I guess if you tried different heads and got the same result..ID should be out... What about the socket depth into the barrel ? A big gap there might do it ?? (ie multimode) ......or a big mismatch w/ no gap at all for that matter ...
603/329-7322
"I fail to see why doing the same thing over and over and getting the
same results every time is insanity: I've almost proved it isn't;
only a few more tests now and I'm sure results will differ this time ... "
"I fail to see why doing the same thing over and over and getting the
same results every time is insanity: I've almost proved it isn't;
only a few more tests now and I'm sure results will differ this time ... "
Hey Jordan and Jack,
Its very well be any number of combos.
I have a few other barrels that will fit. and other heads.
The one I was using didn't gap and I did look at inner dia.
I'll have to try a different size and continue the experiment.
Thanx for the thread Jordan! That was a nice touch.
I don't think I'll need to send it back.
I intended this to be a tinkering project.
I'm sure there is a solution.
I'm interested in what Casey has to say.
Its very well be any number of combos.
I have a few other barrels that will fit. and other heads.
The one I was using didn't gap and I did look at inner dia.
I'll have to try a different size and continue the experiment.
Thanx for the thread Jordan! That was a nice touch.
I don't think I'll need to send it back.
I intended this to be a tinkering project.
I'm sure there is a solution.
I'm interested in what Casey has to say.
Aanvil
-------------------------------------------------
I am not an expert
-------------------------------------------------
I am not an expert
- greenspiderweb
- Posts: 1974
- Joined: Sat Jan 24, 2004 5:23 pm
- antispam: No
- Please enter the next number in sequence: 10
- Location: SE PA near Philly
Yes, yes !greenspiderweb wrote:Casey Burns wrote:If anyone wants, I coulod fit a proper Casey Burns Flute head and foot to that body for half the cost of a new blackwood flute ($350).
Casey
That is a very generous offer by Casey and it most likely will come to that as the real value is on having a bona fide complete Burns but I'm not only a "how" but a "why" kind of person.
I, like some here, have a keen interest in the engineering and physics of flute construction.
These hands on experiments are fun for me.
Nice thing is usually I'm dealing with flutes where I don't have access to the maker other than though a Ouija board.
Aanvil
-------------------------------------------------
I am not an expert
-------------------------------------------------
I am not an expert
- jemtheflute
- Posts: 6969
- Joined: Tue May 23, 2006 6:47 am
- antispam: No
- Please enter the next number in sequence: 8
- Location: N.E. Wales, G.B.
- Contact:
That's really Wylde, Aanvil! So to whom have you access by Ouija? Or are you just loosing your head as well as the flute's????
I respect people's privilege to hold their beliefs, whatever those may be (within reason), but respect the beliefs themselves? You gotta be kidding!
My YouTube channel
My FB photo albums
Low Bb flute: 2 reels (audio)
Flute & Music Resources - helpsheet downloads
My YouTube channel
My FB photo albums
Low Bb flute: 2 reels (audio)
Flute & Music Resources - helpsheet downloads