Chiff and Fipple Forums
http://forums.chiffandfipple.com/

Building a simple flute
http://forums.chiffandfipple.com/viewtopic.php?f=43&t=110987
Page 1 of 1

Author:  scottie [ Sat Aug 22, 2020 3:57 pm ]
Post subject:  Building a simple flute

I would like to build a carbon fiber simple 6 hole flute in G major. Does anyone know where I can get info as to the hole spacing, sizes, length of flute as well as the inside diameter etc. Just do not have the funds to buy one at this time with all the expenses at present ?
Thanks,
Scottie

Author:  Tunborough [ Sat Aug 22, 2020 5:40 pm ]
Post subject:  Re: Building a simple flute

I'm curious why you're proposing carbon fibre. It's not the first material that comes up when people are thinking of making a first flute. Are you planning a conical bore body, or cylindrical?

For the inside diameter of a cylindrical bore flute with G4 as its lowest note, you could start with 18 mm. This table refers to whistles, but there's no reason it doesn't apply to flutes, too: https://www.music.bracker.uk/Music/Searching-For-The-Optimal-Whistle-Bore.html.

For hole layout, I'd suggest WIDesigner, available at https://github.com/edwardkort/WWIDesigner/wiki. The overall length of the flute (if cylindrical) will be around 40 cm, or 16". There are other flute layout calculators available, but I don't have any links at hand.

Perhaps the most important piece of information, though, is how to cut the embouchure hole. With that, I can't be of much help.

Author:  PB+J [ Sun Aug 23, 2020 6:30 am ]
Post subject:  Re: Building a simple flute

Doug Tipple has directions for making a simple flute out of PVC

https://tippleflutes.com/making-a-simple-irish-flute/

There is an online calculators for hole spacing at different keys:

http://iotic.com/flutomat/


Here's another one: http://www.anycalculator.com/pvcpipeflute.html

And this guy has detailad instructions for a PVC pipe flute in G http://www.markshep.com/flute/Pipe.html

Author:  Sedi [ Mon Aug 24, 2020 12:40 pm ]
Post subject:  Re: Building a simple flute

I prefer aluminium over carbon fibre. To "cut" holes in carbon fibre, you need a high-speed milling machine. For aluminium, a simple (less than 100€) box column drill is sufficient. For the hole placement, I use a simple app called "DIY flute" but the overall length you need to get by experimenting, preferrably in a room with the same temperature you wanna play in or the flute will be out of tune. So I first cut the embouchure hole, then cut the tube to size to get the bell note right with my preferred playing style -- embouchure hole slightly covered or not. I'd recommend using a lip plate to get a deeper chimney for the embouchure -- around 3.5 to 4 mm should be okay. It does work without it but the response and tone is much better with a lip plate. But I also made simple two piece flutes just with a tube and a wine cork from plastic. Experiment with the placement of the cork to get the tuning right at the end of the 2nd octave. For a D flute I use 25mm tube with 1.5 mm wall and 22mm inner diameter but that might be too much for a G and the 2nd octave will be difficult to reach. So a smaller size will be better. Bigger holes will make it easier to get the 2nd octave in tune and you can place the cork further away from the embouchure hole which will improve the sound. Be ready for some "trial and error".

Page 1 of 1 All times are UTC - 6 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/